Class pack · 8.10 Buffer capacity
One page for students, then the answer key on its own page. Free to print and share.
AP Chemistry · Unit 8: Acids and Bases

8.10 Buffer capacity

Name: ______________________   Class: ________   Date: ________
Scan to try 3 questions on your phone
The big idea.

Buffer capacity is the amount of strong acid or strong base a buffer can neutralize before its pH changes significantly. It increases with the concentrations of the weak acid and conjugate base, and a buffer resists both acid and base best when [HA]=[AX−][\ce{HA}] = [\ce{A-}], that is, when pH=pKa\text{pH} = \text{p}K_a. A buffer with more AX−\ce{A-} than HA\ce{HA} has more capacity for added acid than for added base.

The lesson (about 15 minutes)

  1. Read the lesson together: https://apchemistrytutoring.com/units/8/8-10-buffer-capacity/
  2. Answer the 5 questions below on your own (about 8 minutes).
  3. Check with the answer key, then scan the QR code for 3 more questions with instant feedback.

Questions

1. Ka of HF is greater than Ka of HIO. Which pair gives the buffer with the greatest capacity?

  1. 0.1 M HIO and 0.1 M NaIO
  2. 0.9 M HF and 0.9 M NaF
  3. 0.9 M HIO and 0.1 M NaIO
  4. 0.1 M HF and 0.7 M NaF

2. A buffer is 1.0 M HCOOH and 0.90 M NaHCOO. Which change increases its capacity to neutralise added acid?

  1. Adding excess HCl
  2. Dissolving more NaHCOO(s)
  3. Adding distilled water
  4. Removing some of the solution with a pipet

3. A buffer has [HA] = 0.80 M and [A⁻] = 0.20 M. Which statement is correct?

  1. Its pH is above pKa and it resists added acid better than added base.
  2. Its pH is below pKa and it resists added base better than added acid.
  3. Its pH equals pKa and it resists both equally.
  4. Its pH is below pKa and it resists added acid better than added base.

4. Four buffers are made. Strong acid is added to each at the same rate. Which will first drop below pH 4?

  1. 1.0 M HOCl / 0.10 M NaOCl (pKa 7.52)
  2. 0.10 M HOCl / 0.010 M NaOCl (pKa 7.52)
  3. 1.0 M HOBr / 0.10 M NaOBr (pKa 8.60)
  4. 0.10 M HOBr / 0.010 M NaOBr (pKa 8.60)

5. Four propanoic acid / propanoate buffers, each with equal concentrations of acid and conjugate base, are titrated with 0.20 M KOH. The volumes of KOH needed to use up all the propanoic acid are 1 mL, 5 mL, 10 mL and 20 mL. Which buffer had the lowest buffer capacity?

  1. The one needing 1 mL
  2. The one needing 5 mL
  3. The one needing 10 mL
  4. The one needing 20 mL

From AP Chemistry Tutoring: the full lesson, more practice and the simulation at https://apchemistrytutoring.com/units/8/8-10-buffer-capacity/

Answer key · 8.10 Buffer capacity

  1. B. It has the highest concentrations of both components in a 1: 1 ratio. The Ka values decide the pH, not the capacity.
  2. B. More HCOO⁻ means more base available to react with added H₃O⁺. Adding water lowers both concentrations (less capacity per litre); removing solution lowers the total moles; excess HCl would destroy the buffer.
  3. B. [A⁻]/[HA] = 0.25 gives pH = pKa − 0.60. With four times more HA, it can neutralise more OH⁻ than H₃O⁺.
  4. B. Capacity for acid depends on the amount of conjugate base; (B) and (D) have the least (0.010 M). (B) also starts at the lower pH (7.52 − 1 = 6.52 versus 7.60 for D), so it reaches pH 4 first once its small amount of OCl⁻ is used up.
  5. A. It contained the fewest moles of propanoic acid (and, since the ratio was 1: 1, of propanoate), so it could neutralise the least added base.

Students can try 3 more questions with instant feedback at https://apchemistrytutoring.com/start/8/?topic=8.10&n=3&utm_source=class&utm_medium=print&utm_campaign=8.10

Chat on WhatsApp